Sony TA-VE800G Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Récepteurs AV Sony TA-VE800G. Sony TA-VE800G User manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1996 by Sony Corporation Printed in Malaysia
3-856-145-11(1)
Getting Started and Basic Operations
TA-VE800G
*Please refer to the TA-VE800G operating instructions for detailed instructions.
Understanding How the Amplifier Works
Integrated AV Amplifier
Using the Remote Control
The remote control supplied with the TA-VE800G uses infrared (IR) rays to command the amplifier and control the on-screen display.
Since this amplifier uses menu operations, you must connect a TV.
Hooking up the System
Notes on connection
• Do not connect the mains lead to an AC outlet or press the
POWER switch before completing all connections.
• The cable connectors should be fully inserted into the
jacks. Loose connection may cause hum and noise.
• Jacks and plugs of the connecting cords are colour-coded as follows:
Red jacks and plugs: Right audio channel
White jacks and plugs: Left audio channel
Yellow jacks and plugs: Video signals
• When you connect two or more VCRs to the unit, make sure to use a
distributor to connect the TV antenna to the VCRs.
• Connect the audio output plug of the CD changer to the CD IN jack
on the unit. If you connect the CD changer to another jack, you won't
be able to use the CD INDEX function.
SATL LD VIDEO 2 VIDEO 1
FRONT SPEAKERS
REAR SPEAKERS CENTER SPEAKER
SWITCHED AC OUTLET
IMPEDANCE USE 4 - 16Ω
LR
++
––
LR
++
––
+
–
IMPEDANCE USE 8 - 16Ω IMPEDANCE USE 8 - 16Ω
MIX
AUDIO
OUT
VIDEO
OUT
VIDEO
IN
AUDIO
OUT
AUDIO
IN
L
R
VIDEO
OUT
VIDEO
IN
AUDIO
OUT
AUDIO
IN
VIDEO
IN
AUDIO
IN
VIDEO
IN
AUDIO
IN
CTRL A1
IR OUT S-LINK
y
TUNER CD DAT/MD TAPE
IN IN REC OUT IN REC OUT IN
L
R
PHONO
IN
MONITOR
to AV 1
to AUDIO/VIDEO IN
to AUDIO/VIDEO OUT
Satellite tuner
to LINE IN
to LINE OUT
to LINE IN
to LINE OUT
Cassette deck
DAT/MD deck
Front speaker (R) Front speaker (L)
TV (MONITOR), etc
to AUDIO/VIDEO OUT
How To Use the Remote
The supplied remote lets you perform
almost all of the amplifier operations.
Operation is simple, press the direction
control button on the remote once to recall
the on-screen display, then press the
corner of the direction control pad
representing the direction you want to
move the pointer (hand shaped icon) on
the on-screen display. Position the pointer
so that the finger tip is positioned on one
of the on-screen items, then press and
quickly release the centre of the direction
control button to “click” the item.
To turn on the amplifier
Press the direction control button on the
remote once or twice to turn on the unit.
Hints on handling the remote
• Do not cover the IR emitter when operating
the remote.
• Hold the remote with its direction control
button facing up, as shown below.
• To make the on-screen display disappear,
position the pointer in the blank area, and
press the centre of the direction control
button.
Direction
control
button
Blank area
Pointer
30°
Be sure your hand
does not cover this part
()0pP=+
FUNCTION
+
–
VOL
ALL
OFF
USERSUB
S
O
U
N
D
PUSH
ENTER
Mm
IR rays
Inserting the Batteries
1
Open the cover on the bottom of the
remote.
2 Insert two size -AA (R6) batteries
with correct polarity (+/–).
3 Close the cover.
To avoid damage caused by battery
leakage and corrosion
Remove the batteries when the
commander will not be used for a long
time.
Setting up Your Amplifier
Registering a TV
Registering a Sony TV
If your Sony TV can be controlled by an
infrared remote, and it is connected to the
amplifier by it’s AV 1 jack, IR code
registration is unnecessary.
Registering a non-Sony TV
Complete the following procedure to set
the amplifier to turn on your TV
automatically whenever you turn on the
amplifier.
1 Turn on the amplifier and the TV set.
Make sure the input selector on the
TV set is set to AV 1.
2 Click FUNCTION in the main menu.
3 Click TV SET.
4 Click OTHER TV (or click “Sony TV”
for a Sony TV).
If you are using a Sony TV
The IR codes are programmed
automatically and registration is complete
(click RETURN or EXIT).
Before going to step 5, cover the IR
sensor on the TV to prevent
accidental operation. Otherwise, the
on-screen display may be turned off
during the programming procedure.
5 Click START.
6 When “PUSH YOUR
COMMANDER” appears on the TV
screen, press the button
on the TV's
remote that corresponds to the
highlighted control button.
Programme the button used to turn
ON your TV (e.g., CH0, CH1, CH+,
etc.) as “CHANNEL 0”.
When programming the IR code,
point the remote at the IR sensor on
the amplifier from a distance no
greater than 10 cm (4 inches) and
hold down the button on the remote
for about 5 seconds until the
instruction “RELEASE YOUR
COMMANDER” appears.
Keep the remote pointed
horizontally at the IR sensor until
the code is programmed.
If you tilt or move the remote during
the programming process, the IR
code may not be programmed
correctly.
7 Repeat this procedure for the
remaining buttons that appear on the
TV screen. If an IR code was not
programmed correctly, the IR code
setting indicator will flash.
TV (monitor)
Video signal
Video signal (Input from source
components combined with on-screen
display)
LD player, etc.
Video signal
VCR, etc.
IR control codes
()0pP=+
FUNCTION
+
–
VOL
ALL
OFF
USERSUB
S
O
U
N
D
1
3
2
Mm
TA-VE800G
On-screen operation
1
The remote commander emits an infrared (IR) signal when you press direction control button (1 above).
2 This controls the movement of the pointer (hand icon) in the on-screen display (2 above).
3 When you move the pointer to an on-screen icon, and press the centre of the direction control button, the infrared (IR) emitter
transmits the corresponding IR control code to the respective programme source (3 above).
If the screen does not appear or the pointer does not move when you press the direction control button
The IR code from the remote is not fully reaching the infrared receptor on the amplifier (1 above). Make sure there are no obstacles between the
remote and the amplifier.
If the programme source fails to respond or is slow to respond
The IR control code from the IR repeater is not fully reaching the infrared receptor on the programme source. Connect the extra IR repeater
(supplied) and position it facing the programme source (see “IR Repeater Hookups” on page 8 of the “Operating Instructions”).
If some of the programmed on-screen controls are unresponsive or slow, rerecord the IR codes for those buttons ( see “Registering non-Sony audio/
video equipment” on page 16 of the “Operating Instructions”).
Camcoder,
TV game, etc
Turntable
to OUTPUT
Tuner
to OUTPUT
CD player
to OUTPUT
VCR 2
VCR 1
to AUDIO/VIDEO OUT
to AUDIO/VIDEO IN
to AUDIO/VIDEO OUT
LD player
to AUDIO/
VIDEO OUT
Registering Audio/
Video Equipment
Registering Sony audio/video
equipment
If your Sony audio and video equipment
can be controlled by an infrared remote,
simply connect them to the jacks shown
on the following table, registration is
unnecessary.
Amplifier jacks Equipment to be
connected
VIDEO 1 Sony VTR 3 (VHS)
VIDEO 2 Sony VTR 1 (BETA)
VIDEO 3 Sony VTR 2 (8 mm)
LD Sony LD player
SATL Sony Satellite decoder
TUNER Sony Tuner
DAT/MD Sony DAT deck
CD Sony CD player (CD 1)
TAPE Sony Tape deck
MONITOR Sony TV
(via its AV 1 jack)
The following cases require registration of
Sony products
• When connecting a Sony MD deck to
the DAT/MD jacks.
• When connecting a Sony audio product
with CONTROL-A1 compatibility.
• When connecting a Sony product to
jacks other than those specified in the
previous table (e.g., when connecting a
Sony LD player to the VIDEO 3 jacks).
• When exchanging non-Sony audio or
video equipment with a Sony product.
Notes
• If your VCR has a COMMAND CODE
selector switch (for VTR 1, VTR 2, or VTR 3),
set the switch to the applicable setting.
• If your CD changer has a COMMAND
MODE selector switch (for CD 1, CD 2, or
CD 3), normally it should be set to “CD 1”.
However, if your CD changer has VIDEO
OUT terminals, set the command mode to
“CD 2” or “CD 3” (“CD 3” should only be
used when making CONTROL-A1
connections).
TV MONITOR SET
TV IR SET
START
Sony TV
OTHER TV
Registering non-Sony audio/video
equipment
1
Click FUNCTION in the main menu.
2 Click IR SET.
3 Click the appropriate function.
4 Click “Sony” for a Sony product or
OTHER for a non-Sony product.
If the programme source is a Sony
product
The IR codes are programmed
automatically and registration is complete
(click RETURN or EXIT).
To take advantage of CONTROL-A1
compatible audio components, such as
multi-disc CD players, click CONTROL-
A1 to select CONTROL-A1.
5 Click the respective programme
source.
(continued)
FUNCTION SELECT
VIDEO 1 DAT/MD
CD
VIDEO 2
TUNER
VIDEO 3
PHONO
L D
TAPESATL
MACRO 1
MACRO 2
EXIT
IR SET
EXIT
VIDEO 1 Sony VTR3
Sony VTR1
Sony VTR2
SATL
DAT/MD
Sony DAT
CD Sony CD1
TAPE Sony TAPE
Sony DBS
Sony LD
IR CODE SETTING
VIDEO 2
VIDEO 3
LD
RETURN
TUNER Sony TUNER
EXIT
OTHERMAKER
IR CODE SETTING
RETURN
Sony
OUTPUT IR
Rear
speaker (R)
Centre
speaker
Rear
speaker (L)
EXIT
OTHERMAKER
IR CODE SETTING
TAPE
DATLD
CD
VCR
RETURN
MD
Sony
OUTPUT IR
TUNER
to VIDEO 3 (input)
on the front panel
FUNCTION SELECT
VIDEO 1 DAT/MD
CD
VIDEO 2
TUNER
VIDEO 3
PHONO
L D
TAPESATL
MACRO 1
MACRO 2
EXIT
TV SET
EXIT
TV MONITOR SET
GRAPHIC POSITION
RETURN
TV IR SET
Sony TV
OTHER TV
IR emitter and
receptor
EXIT
TV IR SET
RETURN
TV IR SET
CHANNEL 0
POWER OFF
PUSH YOUR COMMANDER
CODE CLEAR
WIDE TV DISPLAY MODE
IR sensor
1
2
Résumé du contenu
Page 1 - TA-VE800G
1996 by Sony Corporation Printed in Malaysia3-856-145-11(1)Getting Started and Basic OperationsTA-VE800G*Please refer to the TA-VE800G operating i
Page 2 - Recording
Setting up Your Amplifier (continued)3 When “PUSH YOUR COMMANDER”appears on the TV screen, press thebutton on your VCR’s remote thatcorresponds to the
Plus de documents pour Récepteurs AV Sony TA-VE800G
Sony TA-VE800G Manuel d'utilisateur
(181 pages)
Produits connexes et manuels pour Récepteurs AV Sony TA-VE800G
(64 pages)
(2 pages)
Récepteurs AV Sony HT-IS100 Manuel d'utilisateur
(164 pages)
(164 pages)
(112 pages)
(272 pages)
(148 pages)
(134 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.747 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels