Operating Instructions5GHzWireless LAN AccessPointPCWA-A5004-658-124-11(1)© 2002 Sony Corporation
104 NETWORK 1 connectorUse an Ethernet cable to connect theAccess Point to a DSL modem, cablemodem, or ISDN router.5 NETWORK 2 connectorUse an Etherne
11Getting startedqsqs Factory default switchUse this switch to return the AccessPoint settings to the factory defaultsettings.For details, see “To ret
12About the Access Point initial settingsThe Access Point is configured as follows at shipment.To return the Access Point settings to the factory defa
13Getting startedTo return the Access Point settings to the factory default settingsTo return the Access Point settings to the factory default setting
14Configuring the Access Point settingsTo configure the Access Point settings, use a computer that is connected tothe Access Point using the 5GHz Wire
15Setting and connections• Select Connect using DSL from NETWORK 1 Settings in Easy Setup(page 19) or from NAT Router Mode Settings in NETWORK 1 Setti
16Displaying the Access Point setup pageTo configure Access Point settings, go to the Access Point setup page. Useone of the following three methods t
17Setting and connectionsNoteDepending on the firmware version of the Access Point you are using, the displayedscreen may differ from that shown above
18Display the Access Point setup page by entering the IPaddress in the web browser.1 Connect the Access Point to the AC adapter.z HintThere is no powe
19Setting and connectionsAdministrator passwordIf you set an administrator password, you will be requested to enter a username and password when you o
2WARNINGTo prevent fire or shock hazard, do notexpose the unit to rain or moisture.To avoid electrical shock, do not open thecabinet. Refer servicing
20 Advanced SetupHere, you can configure advanced settings for the Access Point. Further,you can select an operation mode for the Access Point from t
21Setting and connectionsConfirming the status of the Access PointPerform the following steps to confirm the current status of the AccessPoint.1 Follo
22ConnectingConnecting to a DSL modem, cable modem, or ISDN routerIf the Access Point is connected to a DSL modem, cable modem, or ISDNrouter, compute
23Setting and connections1 Connect the Access Point’s NETWORK 1 connector to aDSL modem, cable modem, or ISDN router using anEthernet cable as shown i
24Precautions when mounting the AccessPoint on a wallWhen mounting the Access Point on a wall, the screw size and spacing ofmounting holes is as follo
25Setting and connectionsFastening the Access Point to a wall with screws:Body diameter: 0.14 to 0.29 inches (3.5 to 7.5 mm)Length: 1.2 inches (30 mm)
26PrecautionsAC adapterUse ony the supplied AC adapter. OtherAC adapters may cause a failure in theAccess Point.SafetyDo not drop the Access Point. Ca
27Additional informationSpecificationsPowerAC 100 to 240 V, 50/60 Hz(The power cord plug is for use with AC 120 V.)Power consumptionApproximately 7 WM
28Getting helpThis section describes how to get help and supportfrom Sony, as well as troubleshooting tips for yourWireless LAN Access Point.About Son
29Additional informationGlossaryChannel numberThe frequency used for wirelesscommunications. Wirelesscommunications are available only amongclient com
3NoteThe power outlet should be installed near theequipment and should be easily accessible.Safety InformationWARNING• Opening the unit, for whatever
30WAN (Wide Area Network)A network that interconnects remoteLANs through the Internet or telephonelines.WEPIEEE802.11-compliant security system.Using
31Additional informationTroubleshootingProblems related to the Access Point:Read the Troubleshooting section of this guide before calling SonyCustomer
Printed in Japan❒ The Sony e-mail support service answers your questionsby electronic mail. Just send your question in an e-mail messageand a customer
4Program © 2001, 2002 Sony CorporationDocumentation © 2002 Sony CorporationCopyright © 2000-2001 AtherosCommunications, Inc., All Rights ReservedCopyr
5A PARTICULAR PURPOSE AREDISCLAIMED. IN NO EVENT SHALL THEREGENTS OR CONTRIBUTORS BE LIABLEFOR ANY DIRECT, INDIRECT, INCIDENTAL,SPECIAL, EXEMPLARY, OR
6Table of contentsGetting startedOverview ... 7What you can do with your WirelessLAN Access Point ...
7Getting startedOverviewWhat you can do with your Wireless LAN Access PointThe 5GHz Wireless LAN Access Point PCWA-A500 is designed forconstructing a
8System requirementsIn order to configure the Access Point or check Access Point settings, yourcomputer must satisfy the following hardware and softwa
9Getting startedNames of parts and functionsFront view Side viewPOWERMESSAGEWIRELESSNETWORK 1NETWORK 2214563NETWORK 2Lights green when an Ethernet cab
Commentaires sur ces manuels