Sony MEX-BT3600U Manuel d'utilisateur télécharger pdf

SONY MEX-BT3600U (GB,AR) 3-299-376-51 (1)SONY MEX-BT3600U (GB,AR) 3-299-376-51 (1)

3-299-376-51 (1)

Cautions

Be sure to install this unit in the dashboard of the car

as the rear side of the unit becomes hot during use.

• This unit is designed for negative ground (earth) 12 V

DC operation only.

• Do not get the leads under a screw, or caught in moving

parts (e.g. seat railing).

• Before making connections, turn the car ignition off to

avoid short circuits.

• Connect the yellow and red power input leads only

after all other leads have been connected.

• Run all ground (earth) leads to a common

ground (earth) point.

• Be sure to insulate any loose unconnected leads with

electrical tape for safety.

• Do not cover the ventilation slots or heat sinks of the

unit.

Notes on the power supply lead (yellow)

• When connecting this unit in combination with other

stereo components, the connected car circuit’s rating

must be higher than the sum of each component’s fuse.

• When no car circuits are rated high enough, connect

the unit directly to the battery.

Parts Iist

• The numbers in the list are keyed to those in the

instructions.

• The bracket  and the protection collar  are

attached to the unit before shipping. Before mounting

the unit, use the release keys  to remove the bracket

 and the protection collar  from the unit. For

details, see “Removing the protection collar and the

bracket ()” on the reverse side of the sheet.

• Keep the release keys  for future use as they

are also necessary if you remove the unit from

your car.

Caution

Handle the bracket  carefully to avoid injuring your

ﬁngers.

Catch



Note

Before installing, make sure that the catches on both sides of

the bracket  are bent inwards 2 mm. If the catches are straight

or bent outwards, the unit will not be installed securely and may

spring out.

Connection example

Notes

• Be sure to connect the ground (earth) lead before connecting

the ampliﬁer.

• The alarm will only sound if the built-in ampliﬁer is used.

Installation/Connections

Connection diagram

 To a metal surface of the car

First connect the black ground (earth) lead, then connect the

yellow and red power supply leads.

 To the power antenna (aerial) control lead or

power supply lead of antenna (aerial) booster

ampliﬁer

Notes

• It is not necessary to connect this lead if there is no power

antenna (aerial) or antenna (aerial) booster, or with a

manually-operated telescopic antenna (aerial).

• When your car has a built-in FM/MW/SW antenna (aerial)

in the rear/side glass, see “Notes on the control and power

supply leads.”

 To AMP REMOTE IN of an optional power

ampliﬁer

This connection is only for ampliﬁers. Connecting any other

system may damage the unit.

 To the interface cable of a car telephone

 To the +12 V power terminal which is

energized in the accessory position of the

ignition key switch

Notes

• If there is no accessory position, connect to the +12 V

power (battery) terminal which is energized at all times.

Be sure to connect the black ground (earth) lead to a

metal surface of the car ﬁrst.

• When your car has a built-in FM/MW/SW antenna (aerial)

in the rear/side glass, see “Notes on the control and power

supply leads.”

 To the +12 V power terminal which is

energized at all times

Be sure to connect the black ground (earth) lead to a metal

surface of the car ﬁrst.

Notes on the control and power supply leads

• The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner.

• When your car has built-in FM/MW/SW antenna (aerial) in the

rear/side glass, connect the power antenna (aerial) control

lead (blue) or the accessory power input lead (red) to the

power terminal of the existing antenna (aerial) booster. For

details, consult your dealer.

• A power antenna (aerial) without a relay box cannot be used

with this unit.

Memory hold connection

When the yellow power input lead is connected, power will

always be supplied to the memory circuit even when the ignition

switch is turned off.

Notes on speaker connection

• Before connecting the speakers, turn the unit off.

• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.

• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the

left speaker.

• Do not connect the ground (earth) lead of this unit to the

negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.

• Connect only passive speakers. Connecting active speakers

(with built-in ampliﬁers) to the speaker terminals may damage

the unit.

• To avoid a malfunction, do not use the built-in speaker leads

installed in your car if the unit shares a common negative (–)

lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connection

If speaker and ampliﬁer are not connected correctly, “FAILURE”

appears in the display. In this case, make sure the speaker and

ampliﬁer are connected correctly.

Equipment used in illustrations (not supplied)

Rear speaker

Front speaker

Active subwoofer

Power ampliﬁer

REAR

AUDIO OUT

SUB AUDIO OUT

FRONT AUDIO OUT

 



× 2



× 4



MEX-BT3600U

RCA pin cord (not supplied)

Insert with the cord upwards.

Bluetooth™

Audio System

2008 Sony Corporation Printed in Thailand

Rotary commander RM-X4S

FRONT

AUDIO OUT

SUB REAR

SUB AUDIO OUT

REMOTE

REAR

AUDIO OUT

FRONT

AUDIO OUT

from car antenna (aerial)



AMP REM

Max. supply current 0.3 A

Fuse (10 A)

Blue/white striped

White

Green

Purple

White/black striped

Grey/black striped

Green/black striped

Grey

Left

Right

Left

Right

ANT REM

Max. supply current 0.1 A

Purple/black striped

ATT

Black

Blue

Red

Yellow

Light blue

1 2

Résumé du contenu

Page 1 - Audio System

SONY MEX-BT3600U (GB,AR) 3-299-376-51 (1)SONY MEX-BT3600U (GB,AR) 3-299-376-51 (1)3-299-376-51 (1)CautionsBe sure to install this unit in the dashbo

Page 2 - 2 Remove the bracket 

SONY MEX-BT3600U (GB,AR) 3-299-376-51 (1)SONY MEX-BT3600U (GB,AR) 3-299-376-51 (1)12 3182 mm53 mmDashboardA TOYOTAto dashboard/center consoleBrac

Commentaires sur ces manuels

Pas de commentaire

Sony MEX-BT3600U Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires pour motos Sony MEX-BT3600U. Sony MEX-BT3600U Installation Guide Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour motos Sony MEX-BT3600U