Sony CDX-GT690UI Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non Sony CDX-GT690UI. Sony CDX-GT690UI Installation guide Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
SONY CDX-GT696UI/GT690UI (GB,ES) 4-153-061-51(2)SONY CDX-GT696UI/GT690UI (GB,ES) 4-153-061-51(2)
©2009 Sony Corporation Printed in Thailand
L
R
FRONT
AUDIO OUT
REAR
AU
DIO OUT
BUS
CONTROL IN
REMOTE
IN
*
3
REAR
AU
DIO OUT
FRONT
BUS
IN
SUB OUT (MONO)
3
BUS AUDIO IN
1
2
4
5
6
7
Precauciones
Esta unidad ha sido diseñada para alimentarse sólo con
cc de 12 V de masa negativa.
No coloque los cables debajo de ningún tornillo, ni los
aprisione con partes móviles (p. ej. los raíles del asiento).
Antes de realizar las conexiones, apague el automóvil
para evitar cortocircuitos.
Conecte los cables de fuente de alimentación amarillo
y rojo solamente después de haber conectado los demás.
Conecte todos los cables de conexión a masa
a un punto común.
Por razones de seguridad, asegúrese de aislar con cinta
aislante los cables sueltos que no estén conectados.
Notas sobre el cable de fuente de alimentación
(amarillo)
Cuando conecte esta unidad en combinación con otros
componentes estéreo, la capacidad nominal del circuito
conectado del automóvil debe ser superior a la suma
del fusible de cada componente.
Si no hay circuitos del automóvil con capacidad
nominal suficientemente alta, conecte la unidad
directamente a la batería.
Lista de componentes
• Los números de la lista corresponden a los de las
instrucciones.
La unidad se comercializa con el soporte
y el marco
de protección ya colocados. Antes de montarla,
utilice las llaves de liberación
para extraer el
soporte de la misma. Para obtener más información,
consulte “Extracción del marco de protección y del
soporte ()”.
Conserve las llaves de liberación para
utilizarlas en el futuro, ya que también las
necesitará si retira la unidad del automóvil.
Precaución
Tenga mucho cuidado al manipular el soporte
para
evitar posibles lesiones en los dedos.
Enganche
Nota
Antes de instalar la unidad, compruebe que los enganches de
ambos lados del soporte
están doblados hacia adentro 2 mm.
Si no lo están o están doblados hacia afuera, la unidad no se
instalará correctamente y puede saltar.
Cautions
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow
and red power input leads only
after all other leads have been connected.
Run all ground (earth) leads to a common
ground (earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit’s rating
must be higher than the sum of each component’s fuse.
When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts list
The numbers in the list are keyed to those in the
instructions.
The bracket
and the protection collar are
attached to the unit before shipping. Before mounting
the unit, use the release keys
to remove the bracket
from the unit. For details, see “Removing the
protection collar and the bracket (
)” on the reverse
side of the sheet.
Keep the release keys for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of
the bracket
are bent inwards 2 mm (
3
/32 in). If the catches are
straight or bent outwards, the unit will not be installed securely
and may spring out.
Connection example
Notes (-
A
)
Be sure to connect the ground (earth) lead before connecting
the amplifier.
The alarm will only sound if the built-in amplifier is used.
Tip (-
B)
When connecting only a single CD changer or other optional
device, connect directly to this unit.
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow, and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
To the interface cable of a car telephone
To a car’s illumination signal
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
FRONT
AUDIO OUT
REAR
AUDIO OUT
SUB OUT (MONO)
A
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
Rear speaker
Altavoz posterior
Front speaker
Altavoz frontal
Active subwoofer
Altavoz potenciador
de graves activo
× 2
× 4
B
BUS AUDIO IN
BUS CONTROL IN
Ejemplo de conexiones
Notas (-
A
)
Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplificador.
La alarma sonará únicamente si se utiliza el amplificador
incorporado.
Sugerencia
(-
B
)
Cuando conecte un solo cambiador de CD u otro dispositivo
opcional, hágalo directamente a esta unidad.
Diagrama de conexión
A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y
después los cables amarillo y rojo de fuente de alimentación.
Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
A AMP REMOTE IN de un amplificador de
potencia opcional
Esta conexión es sólo para amplificadores. La conexión de
cualquier otro sistema puede dañar la unidad.
Al cable de interfaz de un teléfono para
automóvil
A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio
del interruptor de encendido
Notas
Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negro a una superficie metálica del automóvil.
Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
Al terminal de alimentación de +12 V que
recibe energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
4-153-061-51(2)
FM/AM
Compact Disc Player
Installation/Connections
Instalación/Conexiones
CDX-GT696UI
CDX-GT690UI
Notes on the control and power supply leads
The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Notas sobre los cables de control y de fuente de
alimentación
El cable de control de la antena motorizada (azul) suministrará
cc de + 12 V cuando conecte la alimentación del sintonizador.
Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control de
antena motorizada (azul) o el cable de fuente de alimentación
auxiliar (rojo) al terminal de alimentación del amplificador de
antena existente. Para obtener más información, consulte a su
distribuidor.
Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
Antes de conectar los altavoces, desconecte la alimentación
de la unidad.
Utilice altavoces con una impedancia de 4 a 8 con la
capacidad de potencia adecuada para evitar que se dañen.
No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del
izquierdo.
No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
No intente conectar los altavoces en paralelo.
Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si la unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.
No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados
correctamente, aparecerá “FAILURE” en la pantalla. Si es así,
compruebe la conexión de ambos dispositivos.
Power amplifier
Amplificador de potencia
AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
Fuse (10 A)
Fusible (10 A)
Blue/white striped
Con rayas azules y blancas
Red
Rojo
Yellow
Amarillo
White
Blanco
Green
Verde
Purple
Morado
White/black striped
Con rayas blancas y negras
Gray/black striped
Con rayas grises y negras
Green/black striped
Con rayas verdes y negras
Gray
Gris
Left
Izquierdo
Right
Derecho
ANT REM
Black
Negro
Blue
Azul
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
Purple/black striped
Con rayas moradas y negras
*
1
from car antenna (aerial)
desde la antena del automóvil
Left
Izquierdo
Right
Derecho
*
1
CD changer
Cambiador de CD
*
2
*
1
RCA pin cord (not supplied)
*
2
Supplied with the CD changer
*
3
Separate adaptor may be required.
*
1
Cable con terminales RCA (no
suministrado)
*
2
Suministrado con el cambiador de CD
*
3
Puede requerirse un adaptador
independiente
Orange/white striped
Con rayas naranjas y blancas
Light blue
Azul celeste
ATT
ILLUMINATION
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Compact Disc Player

SONY CDX-GT696UI/GT690UI (GB,ES) 4-153-061-51(2)SONY CDX-GT696UI/GT690UI (GB,ES) 4-153-061-51(2)©2009 Sony Corporation Printed in ThailandLRFRONTA

Page 2 - TOYOTA B NISSAN

SONY CDX-GT696UI/GT690UI (GB,ES) 4-153-061-51(2)SONY CDX-GT696UI/GT690UI (GB,ES) 4-153-061-51(2)12 3182 mm53 mm12Face the hook inwards.El gan

Commentaires sur ces manuels

Pas de commentaire