Sony RM-V15 Manuel d'utilisateur

3-798-484-21 (1)RemoteCommanderOperating Instructionsi- RM-V15© 1995 by Sony Corporation

3 Press and release the S (Set) button.4 Enter the component's code number.For example, if you're0£)Your Code Numberrur eximipie, n yuu le

step 2: Checking if the Code Number Works1 Power on the component you want to set up using the component’s powerswitch.2 Aim the Remote Commander at

If the Commander Doesn't Seem to Be Working... First, try rep>eating these setup procedures using the other codes listed for your component

Before You Set Up the Second TV, VCR or Cable BoxBefore you set up the Commander to operate components on position OPT (Option"), you must first

ENTER4 Press and release the ENTER button to store the code number in the Commander's memory.To finish setting up the component, go to "Ste

Set the slide switch on the Remote Commander to VCR (to set up a VCR), CBL ' (to set up a cable box), TV (to set up a TV) or ОРТ (to set up the s

Check that the Commander is operating the other functions of your component. Press the charmel and volume - control buttons. If it seems to be worki

3 Press the POWER button to power on/ off the component.POWER ^Note; There may be cases you may turn on/off the cabte box by pressing the

Remote Button DescriptionsI- iRemote ButtonOperatesFunctionTV Changes the input modeVCRSwitches the signals supplied to the TV (from the antenna or fr

Remote ButtonOperates FunctionREC@VCRRecordTo record, press ► while pressing •.First release ► , then release #.(S)VCRStop(E)VCRPauseTVVCRCable boxCh

WARNINGThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These li

Notes on Using the RemoteCommander Using this Commander will not increase the functions of your TV, VCR or cable.l?ox. The fimctions of the Commande

Component Code NumbersTV and VCR CodesBrandComponentCode No.SonyVCR01 (VTR3;VHS)02 (VTR2:8 mm)03 (VTR1;Beta)TV01Admiral (M.Wards) VCR27TV02,14, 09Aiwa

TV and VCR Code Numbers (continued)BrandComponentCode No.Fisher VCR30,34,35,33TV25FunaiVCR38General ElectricVCR29,04,09 -TV02,18,03, 07TV/VCRCombo27(T

BrandComponentCode No.OlympicVCR09,08PanasonicVCR08,09,06,07TV18,16,17,07TV/VCRCombo18(TV)&08,09 (VCR)PentaxVCR05,04PhilcoVCR08,09TV11,f3,03Philip

ITV and VCR Code Numbers (continued)BrandComponent Code No.Sharp VCR27,28TV14,13,15ShintomVCRJ?Signature 2000 (M.Wards)VCR38,27TV14,09SylvaniaVCR10,08

TroubleshootingIf you're having problems settingup or using the RemoteCommander: When setting up the Commander, carefully go through the proced

I Check that the component has infrared remote capability. For example, if your component didn't come with a remote, it probably isn’t capable of

Component No.TVCable BoxVCRIt will be useful to write down the code numbers of your components in the chart above, so that you can refer to them when

Quick Guide to SetupTV, VCR or Cable BoxSecond TV, VCR or Cable BoxSet to TV, VCR or CBLOPT T r CBLVCR-n I I r—TVi L lo.. "J]Set to OPTOPT T I-

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

ContentsInstalling the Batteries...5About This Remote Commander...7If You Do Not Have Sony |Components...

Installing the Batteries Slide open the battery compartment and insert two size AA batteries (not supplied).Be sure to line up the O

Notes on Batteries• Under normal conditions, batteries will last up to six months. If the Remote Commander does not operate.. properly, the batter

About This Remote CommanderThis Remote Commander can operate any of the following video components. If you're using this Commander with a Sony br

ISetting Up the CommanderDetails are on the following pages.TV, VCR, or Cable BoxSecond TV, VCR or Cable BoxSet to TV, VCR or CBLOPTt rCBi.VCH—I \ I

Istep 1: Entering the Code NumberIf you are setting up the Commander to ^operate components using position OPT (Option), you must first complete the p