Sony ICF-C11iP Manuel d'utilisateur télécharger pdf

Personal Audio System

4-450-036-32(1)

ICF-C11iP

Reference Guide

Before operating the system, please read this guide thoroughly

and retain it for future reference.

WARNING

To reduce the risk of fire or electric shock, do

not expose this apparatus to rain or moisture.

To reduce the risk of fire, do not cover the ventilation of the

apparatus with newspapers, tablecloths, curtains, etc. And do

not place lighted candles on the apparatus.

To reduce the risk of fire or electric shock, do not expose this

apparatus to dripping or splashing, and do not place objects

filled with liquids, such as vases, on the apparatus.

Do not install the appliance in a confined space, such as a

bookcase or built-in cabinet.

Do not expose the batteries (battery pack or batteries installed)

to excessive heat such as sunshine, fire or the like for a long time.

As the main plug of AC adaptor is used to disconnect the AC

adaptor from the mains, connect it to an easily accessible AC

outlet. Should you notice an abnormality in it, disconnect it from

the AC outlet immediately.

The nameplate and important information concerning safety are

located on the bottom exterior of the main unit and on the

surface of the AC adaptor.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace

only with the same type.

Notice for customers: the following information is only

applicable to equipment sold in countries applying EU

directives

This product has been manufactured by or on behalf of Sony

Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan.

Inquiries related to product compliance based on European

Union legislation shall be addressed to the authorized

representative, Sony Deutschland GmbH, Hedelfinger Strasse

61, 70327 Stuttgart, Germany. For any service or guarantee

matters, please refer to the addresses provided in the separate

service or guarantee documents.

On copyrights

iPhone, iPod, iPod nano, and iPod touch are trademarks of Apple

Inc., registered in the U.S. and other countries.

Lightning is a trademark of Apple Inc.

“Made for iPod,” and “Made for iPhone” mean that an electronic

accessory has been designed to connect specifically to iPod or

iPhone, respectively, and has been certified by the developer to

meet Apple performance standards. Apple is not responsible for

the operation of this device or its compliance with safety and

regulatory standards. Please note that the use of this accessory

with iPod or iPhone may affect wireless performance.

No Power No Problem is a trademark of Sony Corporation.

Auto Time Set is a trademark of Sony Corporation.

Notes



This unit is not specified for use with an iPad, and malfunction

may result if used with one.



In the Reference Guide, “iPhone” is used as a general reference

to functions on an iPod or iPhone, unless otherwise specified

by the text or illustrations.

Precautions



To disconnect AC power, grasp the plug itself, not the cord.



Since a strong magnet is used for the speaker, keep credit

cards using magnetic coding or spring-wound watches, CRT-

based TVs, or projectors, etc., away from the unit to prevent

possible damage from the magnet.



Do not leave the unit in a location near a heat source such as a

radiator or airduct, or in a place subject to direct sunlight,

excessive dust, mechanical vibration, or shock.



Allow adequate air circulation to prevent internal heat build-

up. Do not place the unit on a surface (a rug, a blanket, etc.) or

near materials (a curtain) which might block the ventilation

holes.



Should any solid object or liquid fall into the unit, unplug the

unit and have it checked by qualified personnel before

operating it any further.



During a thunderstorm, do not touch the antenna (aerial) and

plug.



Do not touch the unit with wet hands.



Do not place the unit anywhere near water.

Notes on the AC adaptor



Use only the supplied AC adaptor. To avoid damaging the

system, do not use any other AC adaptor.

Polarity of the plug



Plug the AC adaptor into a nearby wall outlet (mains). In the

case of a problem, unplug it from the wall outlet (mains)

immediately.



Do not install the AC adaptor in a confined space, such as a

bookcase or built-in cabinet.



To reduce the risk of fire or electric shock, do not expose the

AC adaptor to dripping or splashing, and do not place objects

filled with liquids, such as vases, on the AC adaptor.

NOTES ON LITHIUM BATTERY



Wipe the battery with a dry cloth to assure a good contact.



Be sure to observe the correct polarity when installing the

battery.



Do not hold the battery with metallic tweezers, otherwise a

short-circuit may occur.

Disposal of Old Electrical & Electronic

Equipment (Applicable in the European Union

and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that

this product shall not be treated as household waste. Instead it

shall be handed over to the applicable collection point for the

recycling of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste

handling of this product. The recycling of materials will help to

conserve natural resources. For more detailed information about

recycling of this product, please contact your local Civic Office,

your household waste disposal service or the shop where you

purchased the product.

Applicable accessory: Remote control.

Disposal of waste batteries (applicable in the

European Union and other European

countries with separate collection systems)

This symbol on the battery or on the packaging indicates that

the battery provided with this product shall not be treated as

household waste.

On certain batteries this symbol might be used in combination

with a chemical symbol. The chemical symbols for mercury (Hg)

or lead (Pb) are added if the battery contains more than 0.0005%

mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will

help prevent potentially negative consequences for the

environment and human health which could otherwise be

caused by inappropriate waste handling of the battery. The

recycling of the materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity

reasons require a permanent connection with an incorporated

battery, this battery should be replaced by qualified service staff

only. To ensure that the battery will be treated properly, hand

over the product at end-of-life to the applicable collection point

for the recycling of electrical and electronic equipment.

For all other batteries, please view the section on how to remove

the battery from the product safely. Hand the battery over to the

applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or

battery, please contact your local Civic Office, your household

waste disposal service or the shop where you purchased the

product.

If you have any questions or problems concerning your unit,

please consult your nearest Sony dealer.

Getting started

Connecting to an AC

power source

Connect the AC adaptor (supplied) to the DC IN 6V jack on the

rear of this unit firmly and plug it into a wall outlet.

Notes



Do not twist or place heavy objects on the AC adaptor cord.



To disconnect AC power, grasp the plug itself, not the cord.

About the battery as a backup

power source

This unit contains a CR2032 battery as a backup power source to

keep the clock and the alarm operating during a power

interruption. (No Power No Problem system)

Note for customers in Europe

The clock is preset at the factory, and its memory is powered by

the preinstalled Sony CR2032 battery. If the “0:00” appears in the

display when the unit is connected to AC outlet for the first time,

the battery may be weak. In this case, consult a Sony dealer. The

preinstalled CR2032 battery is considered part of the product,

and is covered by the warranty.

You are required to show “Note for customers in Europe” (in this

instruction) to a Sony dealer in order to validate the warranty for

this product.

When to replace the battery

When the battery becomes weak, “” appears in the display.

If a power interruption occurs while the battery is weak, the

current time and alarm will be erased.

Replace the battery with a Sony CR2032 lithium battery. Use of

another battery may cause a fire or explosion.

To replace the battery, see “Replacing the battery of the unit” for

details.

Connecting the AM loop

aerial

The shape and length of the aerial is designed to receive AM

signals. Do not dismantle or roll up the aerial.

1 Remove only the loop part from the plastic

stand.

2 Set up the AM loop aerial.

Refer to the supplied Startup Guide.

3 Insert the AM loop aerial connector in the AM

ANTENNA jack on the rear of the unit.

To remove the AM loop aerial

Push and hold down the tab of the aerial terminal clamp, and

remove the AM loop aerial.

Remote control

Before using the supplied remote for the first time, remove the

insulation film.

When to replace the battery

With normal use, the battery (CR2025) should last for about 6

months. When the remote can no longer operate the unit,

replace the battery with a new one.

 side facing up

Note



If you are not going to use the remote for a long time, remove

the battery to avoid any damage that may be caused by

leakage or corrosion.

OFF

ALARM

RESET

SNOOZE/BRIGHTNESS

iPhone

RADIO

FM/AM

SNOOZE/BRIGHTNESS

button

ALARM RESET/OFF

button

PRESET/TUNE +/-,

/

buttons

ALARM TIME

SET + button

ALARM A button

ALARM TIME

SET - button

CLOCK/MODE

button

DISPLAY/MEMORY

button

Dock

connector

iPhone  button

RADIO FM/AM

button

VOL +/- buttons

ALARM TIME

SET + button

ALARM B button

ALARM TIME

SET - button

SLEEP button

AUDIO IN

button

DC IN 6V jack

FM wire aerial

AUDIO IN jack

AM ANTENNA jack

Remote sensor

Battery

compartment

The VOL + and  buttons have a tactile dot.

The VOL +, PRESET/TUNE +,  and iPhone  buttons have a tactile dot.

Operations

Setting the clock

To set the clock for the first time

This unit is preset to the current date and time at the factory, and

is powered by a backup battery. All you need to do the first time

is just plug it in and select your time zone.

1 Plug in the unit.

The current CET (Central European Time) appears in the display.

2 Press and hold OFF and CLOCK/MODE for at

least 2 seconds.

Area number “1” flashes in the display.

3 Press ALARM TIME SET + or – repeatedly to

select the number as follows:

Area number Time zone

0 Western European

Time/ Western

European Summer

Time

(default setting)

Central European Time/

Central European

Summer Time

Eastern European Time/

Eastern European

Summer Time

3 Moscow Standard Time

4 Press DISPLAY/MEMORY to set.

Notes



To cancel the time zone setting, press OFF instead of

DISPLAY/MEMORY in step 4.



Though the clock is correctly set at the factory, discrepancies

may arise during transport or storage. If necessary, set the clock

to the correct time by referring to “To set the clock manually.”

When daylight saving time (DST/

summer time) begins

This unit automatically adjusts for daylight saving time (summer

time).

“ ” is displayed from the beginning of daylight saving time

(summer time) and disappears at the end of the daylight saving

time (summer time) automatically.

Auto DST/summer time adjustment is based on GMT (Greenwich

Mean Time).

Area number 0:



Daylight saving time (summer time) begins at: 1:00 AM on the

final Sunday of March.



Standard time begins at: 2:00 AM on the final Sunday of

October.

Area number 1:



Daylight saving time (summer time) begins at: 2:00 AM on the

final Sunday of March.



Standard time begins at: 3:00 AM on the final Sunday of

October.

Area number 2:



Daylight saving time (summer time) begins at: 3:00 AM on the

final Sunday of March.



Standard time begins at: 4:00 AM on the final Sunday of

October.

To cancel Auto DST/summer time

adjustment during the daylight saving time

(summer time) period

The Auto DST/summer time adjustment can be canceled.

Press and hold OFF and DISPLAY/MEMORY on the unit at the

same time for at least 2 seconds while the clock is displayed.

“ ” and “OFF” appear in the display to show that Auto DST/

summer time adjustment has been canceled. The display returns

to the clock.

Notes





Changes to Auto DST/summer time adjustment by the unit

(see above) are subject to circumstances and laws in each

country/region. Should this interfere with desired adjustment,

cancel the Auto DST/summer time adjustment and set the

DST display manually as necessary. Customers living in a

country/region that does not use daylight saving time

(summer time) must cancel Auto DST/summer time

adjustment before using the unit.





To activate Auto DST/summer time adjustment again, press

and hold OFF and DISPLAY/MEMORY on the unit at the same

time for at least 2 seconds.

“ ” and “On” appear in the display to show that Auto DST/

summer time adjustment has been activated. The display

returns to the clock.





When the unit is set to Moscow Standard Time, Auto DST/

summer time adjustment defaults to off. You can turn it on by

the above operation. The beginning and the end of daylight

saving time (summer time) will be the same as area number 2.

To set the clock manually

To change the clock setting manually, operate the unit as follows.

1 Plug in the unit.

2 Press and hold CLOCK/MODE until the year

flashes in the display.

3 Press ALARM TIME SET + or – repeatedly to set

the year, and then press CLOCK/MODE.

4 Repeat step 3 to set the month, day, hour and

minute.

The seconds start incrementing from zero.

Notes





If you do not press any button for about 1 minute while

setting the clock, the clock setting will be canceled.



A 100-year calendar (2013 - 2112) is installed in the unit. When

the date is set, the day of the week is automatically displayed.

MON = Monday, TUE = Tuesday, WED = Wednesday,

THU = Thursday, FRI = Friday, SAT = Saturday, SUN = Sunday

To change the time format

You can choose a time format of the 24-hour system (default) or

the 12-hour system.

Press and hold OFF and SNOOZE/BRIGHTNESS on the unit at

the same time for at least two seconds.

The time format toggles between the 24-hour system (“0:00” =

midnight) and the 12-hour system (“AM 12:00” = midnight).

To display the year and date

During clock display, press DISPLAY/MEMORY once for the date

and month, and press it again for the year.

After a few seconds, the display will change back to the current

time automatically.

Using an iPhone with the

unit

To set an iPhone

1 Open the Dock cover.

2 Hold the unit, and set the iPhone onto the unit

in line with the Dock connector.

When an iPhone is difficult to

set

Push the Dock cover slightly backwards while setting the iPhone.

Note on operating an iPhone

Hold the iPhone when you are operating it.

To remove an iPhone

Hold the unit when removing the iPhone.

Notes



An iPhone in a case or cover can be set on this unit. Remove

the case or cover if it interferes with the Dock connection.



Set the iPhone on the Dock connector firmly.



When setting or removing the iPhone, hold it at the same

angle as the Dock connector on the unit. Do not pull the

iPhone forward too far.



When setting or removing the iPhone, hold the unit securely.



Do not twist or bend the iPhone, as this may result in

connector damage.



Remove the iPhone when transporting it; otherwise, a

malfunction may result.

To charge an iPhone

You can use the unit as a battery charger for an iPhone.

Charging begins when the iPhone is connected to the unit. The

charging status appears in the display of the iPhone. For details,

refer to the user’s guide of the iPhone.

Continued on the reverse side

1 2

Résumé du contenu

Page 1

Page 2

 To set the alarm as iPhone1 Perform steps 1 to 8 in “To set the alarm.”2 Press ALARM A or B to select alarm mode for “iPhone.”The volume level flas

Plus de documents pour Réveils Sony ICF-C11iP

Voir le document Sony ICF-C11iP Manuel d'utilisateur

Sony ICF-C11iP Manuel d'utilisateur (2 pages)

Sony ICF-C11iP Manuel d'utilisateur (6 pages)

Sony ICF-C11iP Manuel d'utilisateur (2 pages)

Sony ICF-C11iP Manuel d'utilisateur (30 pages)

Sony ICF-C11iP Manuel d'utilisateur (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Sony ICF-C11iP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Réveils Sony ICF-C11iP. Sony ICF-C11iP User manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Réveils Sony ICF-C11iP

Commentaires sur ces manuels

Produits connexes et manuels pour Réveils Sony ICF-C11iP