Sony RM-V60 Manuel d'utilisateur télécharger pdf

SONY

Remote Commander RM-V60

Operating Instructions

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to pro\ ide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. Howe\'er, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

For the customers in Canada

The DBS operation works only for digital satellite broadcast system

in the U.S.A.

Setting Up the Remote Commander

Before you can start using the Commander, you must first set it up.

This manual describes everything you need to know to set up the

Commander, including:

• Installing the batteries.

• Presetting the Commander with the codes for your TV, VCR, Cable

box, DBS tuner, and other audio components.

- Presetting the Remote Commander

The Commander is preset at the factory to operate Sony brand

components.

If you're using the Commander with a Sony component, you won't

need to preset the Commander before you start using it.

To set up the Commander to use with other (non-Sony)

manufacturers' components, you'll need to follow the instructions in

this manual to preset the Commander with the correct code number

for your components.

3-861-126-11(1)

Button

Component that can be preset

Factory setting

TV TV

Sony TV

VCR VCR

Sony VHS VCR

(VTR3)

DBS/CBL

DBS tuner/Cable box

Sony DBS tuner

RECEIVER

Receiver

Sony Receiver

CD CD player

Sony CD player

TAPE

Tape deck/MD deck/DAT deck

Sony tape deck

AVI

VCR/Cable box/DBS tuner/

Sony 8n\m VCR

LD player/Receiver/CD player/

(VTR2)

AV2

Tape deck/MD deck/DAT deck

Sony LD player

Note

The Commander can be set up to operate only one component per

button - unless their code numbers happen to be the same. For

example, you cannot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different code

numbers).

Installing the Batteries

Slide open the battery compartment and insert two size AA (R6)

batteries (not supplied).

Be sure to line up the + and - on the batteries with the -r and - on the

battery compartment.

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Commander does not operate properly, the batteries might be worn

out. When the display dims, replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 20 minutes to replace the batteries;

otherwise, your setting of the code numbers will be erased.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte irrside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1; Entering the Code Number

1 See the tables in "Component Code numbers", and find the code

number in double figures for the desired component.

If more than one code number is listed, use the number that's

listed first to complete the steps below.

For example, if you're setting up a Philips' VCR, you would use

the codé number 13.

If your component isn't listed, see "Searching for the Correct

Code".

2' Press the SET button with a bail-point pen tip etc., and release it.

SET

Display window

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Remote Commander RM-V60

Page 2 - RECEIVER CD TAPE AV2

3 l'iv» tlu' W W'K. l'tlîS Oïl . UK'FIN i R.CP. V.\ri\ W'I.oi \\ 2 InilK'n that >. ot iV'poiuis to tlio dos

Page 3 - Using the Remote Commander

Controlling the Volume of Video Components Connected to an Audio SystemThe Commander is factory preset based on the assumption that you hear the sound

Page 4 - Ï4] To change the channel

Remote Button DescriptionsOperating a Cable boxOperating a TVmS3mBÎPreiis before operating a TV. To turn on and off.To change the input mode. To chang

Page 5 - Operating a Tape

Operating a ReceiverOperating a TapeQ] Press tlu' button on which the dosirod component is assigned betöre operating. in To turn on and off. n To

Page 6 - Component Code Numbers

Display windowVolume indicatorSET indicatorTransmission indicatorCurrent operation of the commanderCode numberComponent Code NumbersTV and VCR CodesBr

Page 7 - DBS Tuner Codes Sanyo

Brand Component Code No,Separate ComponentsSiinisung\'CK 25, 1(1, 24Tape Deck CodesT\’20. 12, 13,03TV/\'CR Combo 23, 27 & 24, 25, 2 9Bra

Page 8 - '/2 in.)

Receiver/Amplifier CodesBrandCode No.S<in\01Aiwa22, 27Donoii12, 13, 14Fisher34JVC 05, 06, 40KenwoodJ)3, 04Magnavox35Nakamichi16Onkyo 09, 20Panasoni