Sony CDX-C90 Manuel d'utilisateur télécharger pdf (Page 1)

FM/AM

Compact Disc

Player

Sony Corporation  1998 Printed in Japan

Installation/Connections

CDX-C90

Parts for installation and connections

Installing the rotary remote

Notes

• Choose the mounting location carefully so that the

rotary remote will not interfere with operating the

car.

• Do not install the rotary remote in a place where it

may jeopardize the safety of the (front) passenger in

anyway.

• When installing the rotary remote, be sure not to

damage the electrical cables etc. on the other side of

the mounting surface.

• Avoid installing the rotary remote where it may be

subject to high temperatures, such as from direct

sunlight or hot air from the heater etc.

Example of a mounting location

Choose the exact location for the rotary remote to be

mounted, then clean the mounting surface.

Dirt or oil impair the adhesive strength of the double-sided

adhesive tape.

Mark two positions for the supplied screws.

Use the screw holes on the mounting hardware to mark the

positions.

Marks

Warm the mounting surface and the double-sided

adhesive tape on the mounting hardware to the

temperature of 20°C (68°F) to 30°C (86°F), and attach the

mounting hardware onto the mounting surface by

applying even pressure. Then screw it down with the

supplied screws 8.

Attach a piece of heavy duty tape etc. on the other side of the

mounting surface to cover the protruding tips of the screws so

that they will not interfere with the electrical cables etc. inside

the steering wheel column.

Heavy duty tape etc.

Remove the steering wheel column cover, and drill 2 mm

(

/32 in.) diameter holes where you have marked.

× 2

After installing the steering wheel column

cover, attach the rotary remote to the

mounting hardware by aligning the four

holes on the bottom of the rotary remote to

the four catches on the mounting hardware

and sliding the rotary remote until it locks

into place as illustrated.

Note

If you are mounting the rotary remote to the

steering wheel column, make sure that the

protruding tips of the screws on the inner surface

of the column do not in anyway hinder or interfere

with the movement of the rotating shaft, operative

parts of the switches or the electrical cables etc.

inside the column.

× 2

Installing the Wireless Remote

About the installation site

Before installing the remote, make sure that the

remote can be taken out easily from the location

you are considering and it does not interfere with

the movement of any car-control systems such as

shift lever or emergency brake.

!º

!¡

*I-3-864-350-12*(1)

Attach to the

mounting surface

× 4

Wipe the surface where you plan to install

the remote holder, then attach the holder

with double-sided tape.

Notes

• Direct sunlight may affect the system’s ability to

receive infrared signals from the remote. If this

happens, move the remote closer to the remote

control sensor of the system.

• To prevent deformation due to heat, do not install

the remote in a place subject to direct sunlight.

• When parking you car, put the remote somewhere,

such as the glove compartment, that is away from

direct sunlight to prevent deformation due to heat.

!º

The numbers in the list are keyed to those in the instructions.

Caution

Cautionary notice for handling the bracket 1.

Handle the bracket carefully to avoid injuring your

fingers.

TOP

!™

!£

Holes

1 2 3 4

Résumé du contenu

Page 1 - Compact Disc

FM/AMCompact DiscPlayerSony Corporation  1998 Printed in JapanInstallation/ConnectionsCDX-C90Parts for installation and connections1564237Installing

Page 2 - Installation

InstallationPrecautions•Do not tamper with the four holes on the upper surface of the unit. They are for tuner adjustments to bedone only by service t

Page 3 - Connections

ConnectionsCaution•This unit is designed for negative ground 12 V DC operation only.•Before making connections, disconnect the ground terminal of the

Page 4 - Connection example

Notes on the control leads• The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner.• A power antenna without relay box can