Sony STR-DA4600ES Manuel d'utilisateur Page 47
- Page / 170
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
47
GB
Getting Started
On setting up the active
subwoofer
• When a subwoofer is connected, turn on the
subwoofer and turn up the volume
beforehand. Turn the LEVEL knob to just
before the mid-point.
• If you connect a subwoofer with the
crossover frequency function, set the value
to maximum.
• If you connect a subwoofer with an auto
standby function, set it to off (deactivated).
Note
Depending on the characteristics of the subwoofer
you are using, the setup distance value may be
further away from the actual position.
To use the receiver as a pre-
amplifier
You can use the auto calibration function when
you use the receiver as a pre-amplifier.
In this case, the distance value shown on the
display may differ from the actual distance
value. However, there will be no problems,
even if you continue to use the receiver with
that value.
The auto calibration function allows you to
measure the following:
• Speaker connections
1)
• Polarity of speakers
• Speaker distance
2)
• Speaker size
2)
• Speaker level
• Frequency characteristics (EQ)
2) 3)
• Frequency characteristics (Phase)
2) 4)
1)
The measurement result is not utilized when the
multi-channel input is selected.
2)
The measurement result is not utilized in the
following cases.
– The multi-channel input is selected.
– “2ch Analog Direct” is being used.
3)
The measurement result is not utilized when
Dolby TrueHD, or Linear PCM signals with a
sampling frequency of 176.4 kHz and higher are
being received.
4)
The measurement result is not utilized when
signals with a sampling frequency of 88.2 kHz and
higher are being received.
1 Press MENU.
The menu is displayed on the TV screen.
2 Press V/v repeatedly to select
“ Settings,” then press or
b.
The Settings menu list appears on the TV
screen.
Performing auto calibration
V/v/B/b,
MENU
RETURN/
EXIT O
continued
- Multi Channel 1
- AV Receiver 1
- Owner’s Record 2
- About This Manual 4
- On Copyrights 4
- Table of Contents 6
- Front panel 8
- Indicators on the display 10
- Rear panel 13
- Remote commander 15
- Multifunction remote 16
- Getting Started 19
- 1: Installing speakers 20
- Connecting speakers 22
- ZONE 2 connection 23
- 2: Connecting the monitor 24
- 3: Connecting the video 25
- Notes on connecting cables 26
- Notes on HDMI connections 26
- Audio signals Video signals 28
- B Audio cord (not supplied) 30
- C Video cord (not supplied) 30
- A Audio cord (not supplied) 31
- B Video cord (not supplied) 31
- To the VIDEO 2 IN jacks 32
- Camcorder 32
- INPUT jack 32
- OUTPUT jack 32
- To connect a recording 33
- Notes on converting video 33
- To display Closed Caption 33
- Super Audio CD player 34
- CD player 34
- DIGITAL MEDIA PORT adapter 34
- MD/Tape deck 34
- CD on a Super Audio CD player 35
- 5: Connecting the IR Blaster 38
- 7: Connecting to the 40
- Configuration example 41
- 8: Preparing the receiver 42
- 3 Release the TONE MODE and 42
- 9: Setting the speakers 43
- Selecting the speaker pattern 44
- Setting the surround back 45
- Selecting the front speakers 45
- (Auto Calibration) 46
- Before you perform auto 46
- 6 Press to select “Start.” 48
- 3 Press RETURN/EXIT O 49
- To set the network settings 52
- 1 Turn on your computer and 53
- Referring to help files 54
- Using the menu 54
- To exit the option menus 56
- Playback 57
- Naming the input (Name Input) 58
- Selecting the playback mode 60
- 1 Select the DIGITAL MEDIA 61
- 2 Press OPTIONS 61
- Listening to FM/AM radio 62
- 1 Select “FM” or “AM” 62
- 2 Select “Auto Tuning,” then 62
- 3 Press V/v 62
- 1 Press AMP 62
- Changing the AM tuning scale 63
- Tuning to preset stations 64
- Naming preset stations (Name 64
- Listening to satellite 65
- Connecting a satellite 65
- Checking the ID number 66
- (Antenna Aiming) 66
- (Category Mode) 66
- (Direct Tuning) 67
- (Parental Lock) 68
- Selecting preset channels 68
- 4 Select “ON,” then press 69
- Message list 71
- Enjoying Surround Sound 72
- Press 2CH/A.DIRECT or A.F.D 74
- Press MOVIE 76
- About the network 79
- Registering your favorite 80
- Using a controller 83
- Setting an account 84
- To remove a track, album, or 86
- 3 Select “Yes,” then press 86
- Listening to SHOUTcast 87
- 1 Select “ SHOUTcast” from 87
- Presetting favorite stations 88
- Selecting preset stations 88
- System Requirements 88
- 2 Insert the supplied CD-ROM 89
- 3 Install the Setup Manager 89
- What you can do with the 90
- Multi-zone function 90
- 2:Zone 3 connections 91
- RJ-45 Video Pinout 92
- CAT5 cable 93
- Set the volume control for 94
- (ZONE 2/ZONE 3 operations) 95
- 2 Press ZONE 96
- 3 Press ?/1 96
- What is “BRAVIA” Sync? 97
- Preparing for the “BRAVIA” 97
- Switching the monitors 99
- (Pass Through) 100
- Switching between 101
- (Input Assign) 102
- Using Other Features 103
- (Night Mode) 104
- Recording with a video 105
- Recording with an audio 105
- 2CH/A.DIRECT?/1 106
- To connect speakers 107
- To set up speakers 107
- 5 Press RETURN/EXIT O 108
- Using the setting menu 109
- 1 Press MENU 109
- Auto Calibration 110
- Position 111
- Speaker settings 112
- 1 Select the speaker on the 113
- Test Tone 114
- D. Range Comp (Dynamic range 115
- Distance Unit (Distance unit) 115
- Surround settings 116
- EQ settings 117
- Multi Zone settings 117
- Zone2 Line Out Level 118
- 12V Trigger 118
- Audio settings 119
- Night Mode 120
- Video settings 121
- Zone2 Resolution 122
- HDMI settings 123
- Network settings 124
- External Control 125
- Controllers 125
- Device Name 126
- Rhapsody Account 126
- Network Standby 126
- Quick Click settings 127
- System settings 127
- 1 Press ?/1 to turn off the 128
- Adjusting Settings 131
- To change the display 135
- 2 Press DISPLAY repeatedly 135
- Using Quick Click 137
- 1 Select “ Input” from the 137
- 2 Select the component you 137
- 3 Press QUICK CLICK 137
- Operating the components 138
- 10 key tab 139
- Common tab 140
- ( ) on Common tab 140
- To make the on-screen remote 141
- (Macro Play) 142
- Starting macro play 143
- Operating each 146
- Programming the remote 147
- 4 Press ENTER 148
- To control a VCR 150
- To control a cable box 150
- Program the sequence of the 151
- Clearing all the contents 154
- 2 Release all buttons 154
- Precautions 155
- Troubleshooting 156
- Receiver 159
- To ground 159
- Ground (earth) 159
- Outdoor FM antenna (aerial) 159
- Control for HDMI 160
- Error messages 162
- Clearing the memory 162
- About support information 162
- Specifications 163
- Additional Information 165
Produits connexes et manuels pour Récepteurs et amplificateurs Sony STR-DA4600ES
(2 pages)
(2 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 6.305 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels