Sony AIR-RM10 Manuel d'utilisateur télécharger pdf (Page 2)

1 Make sure that the batteries are

properly inserted.

2 Find your problem in the

checklist below, and take the

indicated corrective action.

If the issue persists, contact your

nearest Sony dealer.

When bringing this unit in for

repairs, be sure to bring in the entire

system (this unit, the S-AIR main

unit and sub units).

This product is a system product,

and the entire system is needed to

determine the location requiring

repair.

The remote commander does

not function.

 Remove any obstacles between the

remote commander and the remote

sensor on the unit, and position the

unit away from fluorescent lights.

 Point the remote commander at the

remote sensor on the unit.

 Move the remote commander closer

to the unit.

 The batteries are running out.

Replace all the batteries with new

ones.

Connecting the unit and S‑AIR

main unit is not possible. (The

“S‑AIR” in the display flashes.)

 If you use another S-AIR main unit,

place it more than 8 m (26

feet)

away from the S-AIR main unit you

are using.

Confirm the S-AIR IDs of the unit

and the S-AIR main unit.

 Place so that the unit and the S-AIR

main unit are separated from other

wireless devices.

 Stop using any other wireless

devices.

 The connected S-AIR main unit is

turned off. Make sure the power

cord is connected and turn on the

S-AIR main unit.

 Check the pairing setting.

 Place so that the unit and the S-AIR

main unit are closer.

 Stop using any equipment that

generates electromagnetic wave such

as a microwave oven.

 Change the S-AIR ID settings of the

unit and the S-AIR main unit.

 Turn off the unit and S-AIR main

unit and then turn them on again.

The S‑AIR channel fails to

change.

Check that the unit and the S-AIR

main unit are connected properly.

When using the Wireless Audio

Transmitter for PC as the S-AIR

main unit, sub unit operations will

not be functional if S-AIR Cast is

not booted or Standard Mode is

selected.

“MULTI MODE INVALID”

appears in the display when

setting the Coupling

operation.

 The main unit cannot be set to the

MULTI MODE. When using the

PARTY mode, the coupling

operation setting is not necessary.

“COUPLING INVALID” appears

in the display when setting the

Coupling operation.

 The main unit cannot recognize the

coupling operation. In this case, the

sub unit cannot also be set on the

Coupling operation.

“COUPLING FAILED” appears in

the display when setting the

Coupling operation.

 This message appears at the

following situation:

– The sub unit tried to be set is not

compatible.

– Two or more sub units accepted

the setting command at the same

time.

– An error occurs at the setting.

“COUPLING ERROR: RETRY”

appears in the display when

setting the Coupling

operation.

 An error occurs at the setting. Try

the setting procedure again.

Display does not turn on (or

only



turns on).

 The batteries are running out.

Replace all the batteries with new

ones.

Messages

PAIRING CANCEL : Time out without

pairing.

PAIRING COMPLETE! : Pairing is

completed.

LINKED : The unit is connected to the

S-AIR main unit.

PAIRING… : Pairing is in progress.

COUPLING… : Coupling is in

progress.

COUPLING ON : Coupling is

completed.

((PLAY)) : This unit cancels the

standby mode, and then starts S-AIR

connecting.

STANDBY : This unit enters into

standby if no button is pressed for a

certain time. Press any key to clear

standby while “STANDBY” is

displayed.

Specifications

Power requirements: LR06 (size AA)

batteries

Battery life: Approx. 5 months

Dimensions: Approx. 53 × 220 × 29

mm (w/h/d) (2

× 8

× 1

in)

Mass: Approx. 132 g (4.6 oz) (not

including batteries)

Supplied accessories:

LR6 (size AA) batteries (4)

Design and specifications are subject

to change without notice.

Listening to sound with an

S‑AIR sub unit

1 Operate the main unit to output

sound.

For details on setting up and

operating the main unit, refer to

the Operating Instructions

supplied with the main unit.

2 Turn on the sub unit by

pressing / (power) of this

unit.

3 Press VOLUME +/– to adjust the

volume.

To identify the unit with a

specific sub unit (Coupling

operation)

If you have two or more sub units, you

can listen to different sound sources on

each sub unit by selecting the MULTI

SOURCE mode.

In MULTI SOURCE mode, since each

sub unit can receive different sound

sources from the main unit, this unit

may not display the correct sub unit

sound source information.

To prevent this, differentiate such sub

units from one another by identifying

(coupling) with the unit.

1 Make sure the sub units and

this unit have all established

connection with the S‑AIR main

unit.

2 Aim the unit at one of the S‑AIR

sub units and press COUPLING.

3 Check that “CPL” blinks, and

then stays on in the display to

indicate coupling was

successful.

If “CPL” does not turn on or an error

message appears, see

“Troubleshooting.”

Note

Use the main unit to set the S-AIR mode.

Refer to the Operating Instructions of the

main unit for details.

Performing play

operations

You can also perform the following

play operations with this unit.

To Press

Start playback. 

Pause playback. ,  or 

Resume playback

during pause.

 or 

Select a track. /

Find a point in a track. Hold down

/ during

playback, and

release the button

at the desired

point

Select preset radio

station.

PRESET +/–

Select the function. S-AIR CH +/–

Viewing information of

the S‑AIR main unit with

iPod dock such as the AIR‑

SA17Ti with this unit

Press DISPLAY.

Note that the title name is always

displayed in the top line when the

S-AIR connection is available.

Each time you press the button, you

can check the following information in

the bottom line of the Information

display lines.

Up to 64 characters of information can

be displayed.

When the unit is connected

Information of S-AIR main unit with

iPod dock such as the AIR-SA17Ti* 

Model name of connected main unit

and the model name of connected sub

unit with coupling operation**  …

* The following information can be viewed,

for example, while playing the iPod.

–Track name

–Artist name

–Album name

–Elapsed playing time of track

When listening to the radio, the frequency

is displayed.

** This information will return to “Title

name” automatically in a few seconds.

Note

Depending on the iPod or iPhone, some

information will not be displayed. For detail,

refer to the Operating Instructions of the

main unit.

Operating S‑AIR main unit with iPod dock

such as the AIR‑SA17Ti with this unit

Listening to sound with an

S‑AIR sub unit

1 Operate the main unit to output

sound using the Remote Mode

or the Advanced Remote Mode.

For details on setting up and

operating the AIR-PC10T, refer to

the Operating Instructions

supplied with the AIR-PC10T.

Turn on the sub unit by pressing

/

(power) of this unit.

3 Press VOLUME +/– to adjust the

volume.

Using on the Remote

Mode

You can perform the following

operations on the Remote Mode of the

S-AIR Cast.

Key operations

To Press

Start playback. 

Stop playback. 

Pause playback. 

Resume playback

during pause.

 or 

Select playlist.* S-AIR CH +/–

Select track. /

* When using Windows Media Player,

“Playlist” and “All Music” changes

alternately.

Contents of the Information

display lines

The title name is displayed in the top

line.

Press DISPLAY and you can change

information displayed in the bottom

line as follows.

Title name (continued from the top

line)  Album name  Artist name

 Genre  Playlist name  Model

name of connected main unit**  ...

Up to 64 characters of information can

be displayed.

** This information returns to “Title name”

automatically in a few seconds.

Tip

When you change playlist, the new playlist

name will be displayed for some seconds.





 Press / to change the top

line (the track is also changed.)

 Press DISPLAY to change the

information that appears in the

bottom line.

Using on the Advanced

Remote Mode

You can perform the following

operations on the Advanced Remote

Mode of the S-AIR Cast.

Key operations

To Press

Start playback. 

Stop playback. 

Pause playback. 

Resume playback

during pause.

 or 

Change Channel

Group.

DISPLAY

Select Channel. S-AIR CH +/–

Select track. /

Contents of the Information

display lines

The title name is displayed in the top

line.

Press DISPLAY and you can change

the Channel Group and information

displayed in the bottom line together

as follows.

Title name  Album name  Artist

name  Genre  iTunes  MED

MGR (Media Manager)  SonicStage

 WMP (Windows Media Player) 

Model name of connected main unit**

 …

Up to 64 characters of information can

be displayed.

** This information returns to “Title name”

automatically in a few seconds.

Examples of operating the

S‑AIR sub unit

Select a

channel by

pressing

S‑AIR CH+/–.

(Example:

Classic)

Select a track

by pressing

/.

(Example: Piano

Concerto)

Select channel

group by

pressing DISPLAY.

(Example: GENRE)





 Press / to change the top

line (the track is also changed.)

 Press DISPLAY or S-AIR CH+/– to

change the bottom line (the channel

group or channel is changed

according to the key operation.)

Operating AIR‑PC10T S‑AIR main unit with

this unit

Operating BD/DVD Home Theatre System

main unit with this unit

Listening to sound with an

S‑AIR sub unit

1 Operate the main unit to output

sound.

For details on setting up and

operating, refer to the Operating

Instructions supplied with the

system.

2 Turn on the sub unit by

pressing / (power) of this

unit.

3 Press VOLUME +/– to adjust the

volume.

Performing play

operations

You can also perform the following

play operations with this unit.

To Press

Start playback of a CD/

DVD, etc.



Stop playback of a CD/

DVD, etc.



Pause playback of a

CD/DVD, etc.



Select a track, file or

chapter of a CD/DVD,

etc.

/

Select a preset station

when listening to the

radio.

PRESET +/–

Select the function. S-AIR CH +/–

Viewing information of

DVD Home Theatre

System with this unit

Press DISPLAY.

Note that some information cannot be

displayed properly, depending on

models.

Each time you press the button, you

can check the following information in

the bottom line of the Information

display lines.

Up to 64 characters of information can

be displayed.

When the unit is connected

Function of connected main unit* 

Model name of connected main unit**



...

* Depending on the model you are using,

information such as following can be

viewed.

–MAIN UNIT

–TUNER FM

–TUNER AM

–DMPORT

–AUDIO

** Displayed for a few seconds.

Troubleshooting

1 2

Remote Commander 1

Commentaires sur ces manuels

Pas de commentaire

Sony AIR-RM10 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Contrôle à distance Sony AIR-RM10