Sony TA-VE800G Manuel d'utilisateur télécharger pdf (Page 2)

Setting up Your Amplifier (continued)

3 When “PUSH YOUR COMMANDER”

appears on the TV screen, press the

button on your VCR’s remote that

corresponds to the control button

highlighted on the TV screen (see step 6

for details).

6 When “PUSH YOUR

COMMANDER” appears on the TV

screen, press the button

on your

audio/video equipment’s remote that

corresponds to the control button

highlighted on the TV screen.

is the POWER switch.

When programming the IR code,

point the remote at the IR sensor on

the amplifier from a distance no

greater than 10 cm (4 inches) and

hold down the button on the remote

for about 5 seconds until the

instruction “RELEASE YOUR

COMMANDER” appears and the IR

code setting indicator turns off.

Keep the remote pointed

horizontally at the IR sensor until

the code is programmed.

If you tilt or move the remote during

the programming process, the IR

code may not be recorded correctly.

Repeat this procedure for the

remaining buttons

After you’ve programmed all the IR

codes, the IR CODE SETTING menu

reappears.

To programme special IR codes that do

not appear as on-screen controls

See “Programming Other Infrared (IR)

Codes (USER IR setting)” on page 20 of

the “Operating Instructions”.

7 Repeat steps 3 to 6 to programme IR

codes from other programme

sources.

Selecting a Component

1 Click FUNCTION in the main menu.

2 Click the component you desire.

The component starts playing

automatically.

3 Click VOL + or – to adjust the

volume.

To show other control buttons for the

selected component

Click SUB.

To execute IR commands programmed from

other remotes

1 Click USER.

2 Click A B C D repeatedly to display the

command you desire.

3 Click the button for the respective

command.

To programme IR codes from other remotes,

see page 20 of the “Operating Instructions”.

To select components using the controls on

the front panel

Press the button for the component you want

to use and start playback from the component.

Components selected in this way can not be

played back with the AUTO PLAY function.

To mute the sound

Click . The icon changes to and

turns green. “MUTE ON” then “MUTING”

appear in the display on the amplifier. To turn

the sound back on, click on the icon again.

To turn off all connected components

Click ALL OFF .

Watching TV or Video programmes

When you watch TV or video

programmes, we recommend you play

audio portion through the amplifier

instead of your TV’s speaker. This lets you

take advantage of the amplifier’s

surround sound effects, like Dolby

Surround, and lets you use the amplifier’s

remote to control the audio.

Turn off the speakers on your TV before

you start so you can enjoy the surround

sound from your amplifier.

Watching TV programmes

You can use the TV tuner built in to your

video deck to watch TV programmes using the

amplifier’s on-screen operations.

1 Select the appropriate function (e.g. “VIDEO

2”).

2 Click TVb in the VCR controls at the

bottom of the screen.

The control panels switches to the video

decks’s TV controls.

3 Click CH – or + to change the programme

position.

To return to the VCR controls, click VTRb.

We recommend switching to the VCR controls

before switching functions. If you leave

directly from the TV controls to the

FUNCTION SELECT menu, the AUTO PLAY

(page 37 of the “Operating Instructions”)

function will not operate the next time you

select the video deck as a programme source.

To select TV programme positions

directly when watching TV programmes

using the built-in tuner on your VCR

Click SUB in the video deck control panel

to display the direct selection controls.

When using a non-Sony VCR, be sure to

programme -/-- or 1- and 2- codes

manually as shown on page 17 of the

operating instructions.

These codes are not pre-programmed in

this unit.

To change the video input of a Sony VCR

Click the INPUT icon in the video deck control

panel.

Likewise, to watch a TV programme after

watching a video tape, stop the VCR, click

INPUT, then use the on-screen controls to

select the desired programme position.

To switch the screen size when using a wide

TV monitor

Click repeatedly to select the screen size

you desire.

Using Pre-programmed

Sound Fields

You can take advantage of surround

sound simply by selecting one of the pre-

programmed sound fields according to

the programme you want to play.

1 While playing a programme source,

click SOUND in the main menu.

2 Click a sound field genre to select the

type of sound field you desire.

The previously selected mode turns

on automatically.

3 Click MODE repeatedly to select the

mode you desire from the respective

genre.

To increase the bass

Click on BASS BOOST ON.

To play without surround effects

Select “ACOUSTIC” from MUSIC 2. The

surround effects are defeated but you can still

adjust the tone (see page 29 of the “Operating

Instructions”).

To turn off the sound fields

Click SOUND FIELD ON/OFF.

Recording

You can record on a cassette tape, Digital

Audio Tape, MiniDisc, or video tape (etc.)

using the amplifier. See the instruction

manual of your recording component if

you need help.

1 Click FUNCTION in the main menu.

2 Click the programme source you

want to record (“LD” for example).

3 Click SUB.

4 Click REC EDIT.

5 Click the component you want to

record to (“VIDEO 1” for example).

The control panels for both

components appear on the TV screen.

“PLAYER” for the programme

source, and “RECORDER” for the

programme destination.

The green arrow indicates the source

component.

When recording, the green arrow

should be next to “PLAYER”.

Clicking a RECORDER control while

recording cuts off the programme

source (PLAYER).

6 Insert a blank tape into the recording

component (or VCR, etc.) and adjust

the recording level, if necessary.

7 Click the REC to start recording, then

click the PLAYER ( control.

Recording begins.

To control the recorder (when not

recording)

Click RECORDER. “RECORDER” becomes the

source component and you can use the

RECORDER controls to rewind and playback

the recording (etc.). Click PLAYER to return

control to the original source component.

To monitor the recorded sound when

recording to a 3-head cassette deck

1 Click EXIT.

2 Click FUNCTION in the main menu.

3 Click TAPE.

To stop recording

Click on p of the recording unit.

To return to the main menu

Click EXIT.

Notes

• There is no sound output from the recording

component even though all the buttons on

the recording unit’s control panel are

operational.

• If you click RECORDER during recording,

the source being recorded will be cut off.

• If you leave the REC EDIT menu by clicking

FUNCTION, SOUND, or EXIT, recording

continues, but control returns to the

PLAYER side, even if you previously

clicked RECORDER.

• If you open the FUNCTION SELECT menu

and click another programme source while

recording, the newly selected programme

source will be recorded.

• Some cassette decks require that you press

the r REC and ( buttons simultaneously

to start recording. To perform one-button

from the on-screen display, be sure to

record the recording signal as shown in

steps 1 to 7 of “Registering non-Sony audio/

video equipment” (pages 16 to 19 of the

“Operating Instructions”) for both Sony and

non-Sony products.

• Sound input through the TAPE connectors

on the rear panel cannot be recorded on a

recording unit.

If the equipment is not a video deck or

laser disc player

Cover the IR sensor on the equipment to

prevent accidental operation during the

programming procedure, click START,

then go to step 6.

If the equipment is a video deck or

laser disc player:

1 Click START.

A list of other manufacturers appears.

2 Click the manufacturer of the

respective equipment and the IR codes

for that programme source are

registered automatically. (If the

manufacturer is not listed, cover the IR

sensor on the equipment to prevent

accidental operation during the

programming procedure, click

“OTHER”, then go to step 6).

3 Click TEST.

If the selected programme source turns

on, it means the IR codes have been

registered. This ends the procedure.

If the programme source does not turn

on, click the number button beside the

manufacturer’s name to select another

number, then click TEST again. If the

programme source still does not turn

on, cover the IR sensor on the

equipment to prevent accidental

operation during the programming

procedure, click “OTHER”, then go to

step 6.

When using a video deck from another

manufacturer

Check to see if the supplied remote uses -

/-- or 1- and 2- buttons to enter 2 digit

programme positions.

Since the -/-- or 1- and 2- codes are not

pre-programmed in this unit, do the

following operations to programme these

codes manually.

1 Select the manufacturer (as shown in

step 2 above).

2 Click -/-- 2- CODE SET.

EXIT

OTHERMAKER

IR CODE SETTING

TAPE

DATLD

VCR

RETURN

Sony

START

OUTPUT IR

TUNER

FUNCTION

–

VOL

ALL

OFF

USERSUB

)(0pP=+

FUNCTION SELECT

VIDEO 1 DAT/MD

VIDEO 2

TUNER

VIDEO 3

PHONO

L D

TAPESATL

MACRO 1

MACRO 2

EXIT

FUNCTION

–

VOL

ALL

OFF

USERSUB

)(0pP=+

SOUND FIELD SELECT

SOUND FIELD

BASS BOOST

PRO LOGIC

MOVIE

MUSIC 1

MUSIC 2

SPORTS

GAME

–

VOL

EXIT

SOUND FIELD SELECT

EXIT

SOUND FIELD

BASS BOOST

PRO LOGIC

MOVIE

MUSIC 1

MUSIC 2

SPORTS

GAME

MODE

OFF

–

VOL

FUNCTION

–

VOL

ALL

OFF

EXIT

SIDE

5 4 3 2 1

6 7 8 9

10/0

REC EDIT

USER

)(0pP=+

SIDE

+10

USERSUB

)(0pP=+

FUNCTION

–

VOL

ALL

OFF

RECORDER

EXIT

TAPE

DAT / MD

VIDEO 2

VIDEO 1

PLAYER

()0pP

FUNCTION

RECORDER

ALL

OFF

REC

EXIT

VIDEO 1

(+=pP

L D

PLAYER

–

VOL

green arrow

()0pP

FUNCTION

RECORDER

ALL

OFF

REC

EXIT

VIDEO 1

(+=pP

L D

PLAYER

–

VOL

• When you record on a DAT or MD

connected to the DAT/MD REC OUT jacks,

sound adjustments do not effect the

recording.

EXIT

– / – – 2 – CODE SET

RETURN

OTHER

TEST

VCR MAKER SETTING

PHILIPS

ZENITH

HITACHI

SHARP

GRUNDIG

SANYO

RCA

TOSHIBA

JVC

PANASONIC

FISHER

AKAI

EMERSON

1 2

1 21 2 3 4

1 2

1 2 3 4

1 2

MISTUBISHI

1 2 3

Operations

EXIT

IR CODE SETTING

10/0

>10

REC

5 6 7 8

RETURN

)(0pP=+

PUSH YOUR COMMANDER

CODE CLEAR

EXIT

–/–– 2– CODE SETTING

RETURN

PUSH YOUR COMMANDER

CODE CLEAR

2 –

– / ––

CODE

– / ––

2 –

1 –, CODE

1 2

Commentaires sur ces manuels

Pas de commentaire

Sony TA-VE800G Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Sony TA-VE800G