Sony DVP-S525D Manuel d'utilisateur Page 12

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 68
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 11
12
Getting Started
If you have a digital component such as a
receiver (amplifier) with a digital connector, DAT
or MD
Connect the component via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied).
When you play a DVD, set “DIGITAL OUT” in “AUDIO SETUP”
to “ON” and then set “DOLBY DIGITAL” to “D-PCM,” “MPEG”
to “PCM” and “DTS” to “OFF” in the setup display (page 51).
pWhen using an optical digital connecting cord
Take off the cap and plug in the optical digital connecting cord.
pWhen using a coaxial digital connecting cord
Notes
• Refer to the instructions supplied with the component to be
connected.
• You cannot make digital audio recordings of discs recorded in
multi-channel surround format directly using an MD deck or
DAT deck.
When you make the connections above, do not set
“DOLBY DIGIT AL” to “DOLBY DIGIT AL,” “MPEG” to “MPEG”
and “DTS” to “ON.” If you do, a loud noise will suddenly
come out from the speakers, affecting your ears or causing
the speakers to be damaged.
Optical digital connecting cord
(not supplied)
CD/DVD player
Receiver (Amplifier)
with a digital
connector, MD deck,
DAT deck, etc.
Coaxial digital connecting cord
CD/DVD player
Receiver (Amplifier)
with a digital
connector, MD deck,
DAT deck, etc.
If you have an audio component with a built-in
DTS decoder, Dolby Digital decoder or MPEG
decoder
Connect the component via the DIGITAL OUT OPTICAL or
COAXIAL connector using an optical or coaxial digital
connecting cord (not supplied).
p When you play a DVD that is recorded in DTS format
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then
set “DTS” to “ON” in the setup display (page 51).
p When you play a DVD that is recorded in Dolby Digital
format
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then
set “DOLBY DIGITAL” to “DOLBY DIGIT AL” in the setup
display (page 51).
p When you play a DVD that is recorded in MPEG format
Set “DIGITAL OUT” in “AUDIO SETUP” to “ON” and then
set “MPEG” to “MPEG” in the setup display (page 51).
Notes
• Refer to the instructions supplied with the component to be
connected.
When you do not connect an audio component with a
built-in DTS decoder, do not set “DTS” to “ON.”
When you do not connect an audio component with a
built-in DOLBY DIGITAL decoder, do not set “DOLBY
DIGIT AL” to “DOLBY DIGITAL.”
When you do not connect an audio component with a built
in MPEG decoder, do not set “MPEG” to “MPEG.”
CD/DVD player
Audio component
with a built in
DTS decoder,
DOLBY DIGITAL
decoder or MPEG
decoder
Optical or coaxial digital
connecting cord
Speakers
Receiver (Amplifier) Hookups
(not supplied)
OPTICAL COAXIAL
DIGITAL IN
OPTICAL
DIGITAL OUT
PCM/DTS/MPEG
DOLBY DIGITAL (AC-3)
DIGITAL IN
COAXIAL
OPTICAL COAXIAL
DIGITAL OUT
PCM/DTS/MPEG
DOLBY DIGITAL (AC-3)
Vue de la page 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 67 68

Commentaires sur ces manuels

Pas de commentaire