Sony STR-DA1200ES Manuel d'utilisateur Page 43
- Page / 111
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
43
GB
Getting Started
1 Confirm the measurement
result.
When the measurement ends, a beep
sounds and the measurement result
appears on the display.
2 Press V/v repeatedly to select
the item, then press .
3 Press V/v repeatedly to select a
preset number to be used, then
press .
4 Press .
The measurement results are saved.
Tip
The size of a speaker (LARGE/SMALL) is
determined by the low characteristics. The
measurement results may vary, depending on the
position of the optimizer microphone and speakers,
and the shape of the room. It is recommended that
you follow the measurement results. However, you
can change those settings in the Speaker Settings
menu (page 63). Save the measurement results first,
then try to change the settings if you want.
When error codes appear
Try the remedies and re-perform the auto
calibration.
Confirming/saving the
measurement results
Measurement
result
Display Explanation
When the
measurement
process
completes
properly
COMPLETE
Proceed to step
2.
When the
measurement
process fails
ERROR
CODE XX
See “When
error codes
appear” (page
43).
Item Explanation
RETRY Re-performs the auto
calibration.
SAVE EXIT Saves the measurement
results and exits the setting
process.
WRN CHECK Displays a warning
concerning the
measurement results. See
“When you select “WRN
CHECK”” (page 44).
PHASE INFO Displays the phase of each
speaker (in phase/out of
phase). See “When you
select “PHASE INFO””
(page 44).
DIST.INFO Displays the measurement
result for speaker distance.
LEVEL INFO Displays the measurement
result for speaker level.
EXIT Exits the setting process
without saving the
measurement results.
Error code Cause and remedies
CODE 31 SPEAKERS (OFF/A/B/A+B) is
set to OFF. Set it to others and re-
perform the auto calibration.
CODE 32 None of the speakers were
detected. Make sure that the
optimizer microphone is
connected properly and re-
perform the auto calibration.
If the optimizer microphone is
connected properly but the error
code appears, the optimizer
microphone cable may be
damaged or improperly
connected.
CODE 33 (F) None of the front speakers are
connected or only one front
speaker is connected. The
optimizer microphone is not
connected.
Item Explanation
continued
- Multi Channel 1
- AV Receiver 1
- For customers in Europe 2
- About This Manual 3
- Table of Contents 4
- Using the Remote 5
- Additional Information 5
- Front panel 6
- Rear panel 11
- E VIDEO/AUDIO INPUT/OUTPUT 12
- F SPEAKERS section 12
- Remote commander 13
- Name Function 14
- Getting Started 15
- 1: Installing speakers 16
- 2: Connecting speakers 17
- How to hook up your 19
- Connecting components with 20
- CD on a Super Audio CD player 21
- HDMI jacks 25
- Notes on HDMI connections 26
- Connecting a TV monitor 27
- Connecting a DVD player/DVD 29
- Connecting a DVD recorder 30
- Connecting a satellite tuner 31
- Closed Caption display 34
- To connect a recording 34
- Connecting the AC power cord 36
- (mains lead) 36
- Performing initial setup 36
- Inserting batteries into the 37
- About the command mode 37
- Setting the speaker impedance 38
- Selecting the front speaker 39
- 7: Calibrating the 40
- Performing auto calibration 41
- 9 Measurement starts 42
- 1 Confirm the measurement 43
- 4 Press 43
- When you select “WRN CHECK” 44
- When you select “PHASE INFO” 44
- Auto Calibration menu 45
- Playback 47
- An example of the display 48
- MULTI CHANNEL DECODING lamp 49
- • Refer to the operating 50
- TV and video game 50
- Amplifier Operations 52
- Overview of the menus 53
- Adjusting the level (Level 56
- Adjusting the equalizer 57
- Settings for the surround 59
- Using the surround back 60
- Settings for the tuner 61
- Settings for the audio 62
- Settings for the video 63
- Settings for the speakers 63
- (Surround speaker) 64
- (Surround back speakers) 64
- (Surround speaker position) 66
- Settings for the system 67
- Calibrating the 68
- Enjoying Dolby Digital 69
- Type of A.F.D. mode 70
- Selecting a pre 71
- Using only the front 73
- Enjoying the surround 73
- (ANALOG DIRECT) 74
- (TEST TONE) 74
- Resetting sound fields to 76
- 2 While holding down MUSIC 76
- Listening to FM/AM radio 77
- 1 Press TUNER repeatedly to 77
- 2 Press TUNING +/– 77
- (AUTOBETICAL) 78
- Direct tuning 78
- Presetting radio stations 79
- Tuning to preset stations 80
- Naming preset stations 80
- Receiving RDS broadcasts 81
- Displaying RDS information 81
- Description of program types 82
- Other Operations 83
- (INPUT MODE) 85
- (DIGITAL ASSIGN) 86
- (HDMI ASSIGN) 87
- (COMPONENT VIDEO ASSIGN) 88
- 6 Press 89
- 8 Press 89
- Changing the display 89
- Recording onto a MiniDisc or 90
- To record digital sound 91
- To connect speakers 91
- To set up speakers 91
- To cancel programming 94
- The numeric codes 94
- To control a VCR 96
- To control a DVD player 96
- To control a DVD recorder 96
- To control a TV 96
- Press and hold MASTER VOL – 97
- Release MASTER VOL – 97
- Glossary 98
- Precautions 100
- Troubleshooting 101
- Remote control 104
- Specifications 105
- Frequency response 106
- FM tuner section 106
- AM tuner section 106
- (Models for countries/areas 107
Produits connexes et manuels pour Récepteurs AV Sony STR-DA1200ES
(134 pages)
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.538 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels