Sony RM-AV2100B Manuel d'utilisateur Page 27
- Page / 76
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
27
1 While pressing COMMANDER
OFF, press the SYSTEM
CONTROL button (1 or 3).
The programmed key operations are
displayed in order.
2 While pressing the RESET key,
press the SYSTEM CONTROL
button (1 or 3).
When the contents of its program are
cleared, all the components names
flash.
3 While pressing the RESET key,
press the SYSTEM CONTROL
button (1 or 3) again.
When it is reset to the factory setting,
the programmed operations are
displayed in order.
Note
The interval setting (page 30) is not reset to the
factory setting, even if you perform these steps.
Notes on System Control
Operations
•If the remote control detectors of the
components are too far apart, or if
something is blocking them, some of
the components may not operate
consecutively even after you press the
SYSTEM CONTROL button.
•If some of the components did not
operate correctly because of the above
or for any other reason, always set all
the components back to the states they
were in before you pressed the SYSTEM
CONTROL button. Failure to do this
can result in incorrect operation when
you press the SYSTEM CONTROL
button again.
•Some components may not always be
powered on by the System Control
function. This is because the power of
the component gets on and off
alternatively when receiving the power
on/off signal. In this case, check the
operating component’s power on/off
state before using the system control
function.
•If the system control function does not
work correctly, see also “Tips for
programming the System Control
functions” on page 25.
Continued
- Integrated Remote 1
- Commander 1
- For the customers in the USA 2
- Owner’s Record 2
- NOTICE FOR THE CUSTOMERS IN 2
- THE U.S.A 2
- Features 3
- Table of Contents 4
- Using Other Functions 5
- Additional Information 5
- Appendix 5
- Installing the Batteries 6
- Location and Function 7
- Setting the Code for 8
- Preset Audio and Visual 8
- Components 8
- Note on the DVD and CBL/SAT 9
- Note on the DECK B/A button 9
- Checking if the code number 10
- 1 Press the corresponding 10
- 3 Aim the Commander at the 10
- 5 Press COMMANDER OFF 11
- Finding a component code 11
- Remote Commander 13
- Operating Your 13
- Components with the 13
- To control the volume 14
- 3 When you are done using the 14
- Notes on operating your 15
- Using Non-Preset 16
- Remote Control 16
- Operations 16
- 6 Press COMMANDER OFF 17
- 2 When the desired display 19
- After Step 2 (page 16), while 20
- Press COMMANDER OFF 20
- 1 While pressing COMMANDER 21
- 3 Press COMMANDER OFF 21
- Controlling the Volume 22
- Connected to an Audio 22
- Executing a Series of 23
- Commands 23
- 2 Press the Component Select 24
- Programming a series of 24
- CONTROL buttons 24
- 4 Repeat Steps 2 and 3 and 25
- Notes on System Control 27
- Select buttons 28
- Component 30
- Display for the 30
- SYSTEM CONTROL 30
- 1, 2, 3 buttons 30
- Adding an Extra 31
- Function to the 31
- Component Select 31
- Adding a command that is 32
- 1 Place the RM-AV2100 head to 33
- 2 While pressing COMMANDER 33
- 3 Press the desired Component 33
- Turning Off the Power 34
- Assigning Other 35
- Components to the 35
- 3 Press the ENTER key 36
- 4 •If the newly assigned 36
- Copying the settings of a 37
- Component Select button to 37
- Programming a 38
- Frequently Used Key 38
- Operation for SYSTEM 38
- CONTROL Buttons 38
- 1 Place the Commander head to 39
- 3 Press the SYSTEM CONTROL 39
- Notes on learning the signals 40
- Transferring Data 41
- Commanders 41
- To transfer the data of a 42
- Component Select button 42
- 7 Press the “ENTER” key 43
- Receiving the data 43
- To receive the data of a 44
- Component Select button from 44
- Selecting a Channel 45
- 4 Release the macro key (PIP 46
- Locking the Controls 47
- Protecting your 48
- Changing the Auto 49
- Power-Off Time of the 49
- Adjusting the Backlight 50
- Setting the Key-Touch 51
- Changing the Touch 52
- Key Display 52
- Specifications 54
- Precautions 54
- Maintenance 54
- Troubleshooting 55
- Troubleshooting (continued) 56
- Customer Support Information 57
- Table of Preset 58
- Functions 58
- VCR 1, 2, 3 59
- CBL (Cable box) 60
- VD (Video disc player) 60
- Continued 61
- Table of Preset Functions 62
- (continued) 62
- DECK B/A 64
- DSP (Digital Surround 65
- Processor) 65
- LCD Touch-Key Display Table 66
- (Video disc 68
- (cable box) 69
- (Digital 72
- Surround 72
- Full display 73
- Quick Reference of Operations 74
Produits connexes et manuels pour Télécommandes Sony RM-AV2100B
(2 pages)
(2 pages)
(1 pages)
(2 pages)
(104 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.523 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels